In a situation where the amplification mechanism is faulty, then your sound system is likely to give a poor output. The work of an amp is to raise the level of an electrical signal to a level that can be fed to the targeted output device which can be a speaker or a headset. This means if the speaker is producing a weak sound, the problem can be traced back to the amp and correction made. Amplifier repair may be required also if the output is distorted or it is not clear.
Most amplification systems are easy to troubleshoot as they are constructed such that it is possible to view all components once the covers are removed. Several steps are followed when undertaking repair for an audio system. The first one normally involves removing the device form its position and placing it on a table.
A screwdriver is applied in loosening the side and top covers of the appliance. Once all components are visible, technicians normally look if there are components which are burned before they embark on sophisticated troubleshooting procedures. If the system had just failed, an odor will suggest that there is a burned component like a resistor or a transistor.
All power transistors in the system can be identified by use of the service manual obtained from the manufacturer. The power button is put on and a multimeter applied in determining if there is voltage on the pins of these transistors. The rest of the power ICs need to be identified and the same test done on them. The fuse will be tested for continuity and if found to be blown, replacement with a suitable one will be done.
Troubleshooting can proceed to other parts of the device if its power supply is fixed. A freezer will be used to look for presence of faulty components in the system. What happens is that all components are given a short burst and then the power put on. The last element to clear moisture is the one which is damaged.
When removing an element that is found to be spoiled, a heat gun is used to melt the solder holding it onto the board. After melting is achieved, a pliers is applied in pulling the pins from the PCB. It is required that you get the board out of its position so that you can access both sides. The holes left behind are cleaned with help of a solder wick.
Through use of the manual, it is possible to identify the component that is not working. A new one is then acquired and soldered at the same position and orientation. While inserting the pins of the element into the holes, one should be careful so that he does not bend them. Only enough solder should be applied so that the pins are not short. A side cutter is applied in clipping off the excess pins so that they do not protrude from the underside of the circuit board.
Once replacing a spoiled component is finished, the board is fastened back to its position. The device is then plugged in and the power turned on. If the system is confirmed to be working as required, the power is put off and the covers replaced.
Most amplification systems are easy to troubleshoot as they are constructed such that it is possible to view all components once the covers are removed. Several steps are followed when undertaking repair for an audio system. The first one normally involves removing the device form its position and placing it on a table.
A screwdriver is applied in loosening the side and top covers of the appliance. Once all components are visible, technicians normally look if there are components which are burned before they embark on sophisticated troubleshooting procedures. If the system had just failed, an odor will suggest that there is a burned component like a resistor or a transistor.
All power transistors in the system can be identified by use of the service manual obtained from the manufacturer. The power button is put on and a multimeter applied in determining if there is voltage on the pins of these transistors. The rest of the power ICs need to be identified and the same test done on them. The fuse will be tested for continuity and if found to be blown, replacement with a suitable one will be done.
Troubleshooting can proceed to other parts of the device if its power supply is fixed. A freezer will be used to look for presence of faulty components in the system. What happens is that all components are given a short burst and then the power put on. The last element to clear moisture is the one which is damaged.
When removing an element that is found to be spoiled, a heat gun is used to melt the solder holding it onto the board. After melting is achieved, a pliers is applied in pulling the pins from the PCB. It is required that you get the board out of its position so that you can access both sides. The holes left behind are cleaned with help of a solder wick.
Through use of the manual, it is possible to identify the component that is not working. A new one is then acquired and soldered at the same position and orientation. While inserting the pins of the element into the holes, one should be careful so that he does not bend them. Only enough solder should be applied so that the pins are not short. A side cutter is applied in clipping off the excess pins so that they do not protrude from the underside of the circuit board.
Once replacing a spoiled component is finished, the board is fastened back to its position. The device is then plugged in and the power turned on. If the system is confirmed to be working as required, the power is put off and the covers replaced.
No comments:
Post a Comment